--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/pins.h Sat Nov 07 13:23:07 2015 +0100
@@ -0,0 +1,165 @@
+#ifndef _PINS_H
+#define _PINS_H
+
+/****************************************************************************************
+* Sanguinololu pin assignment
+*
+****************************************************************************************/
+#if MOTHERBOARD == 62
+#define KNOWN_BOARD 1
+#ifndef __AVR_ATmega644P__
+#ifndef __AVR_ATmega1284P__
+#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
+#endif
+#endif
+
+#define X_STEP_PIN 15
+#define X_DIR_PIN 21
+#define X_MIN_PIN 18
+#define X_MAX_PIN -1
+
+#define Y_STEP_PIN 22
+#define Y_DIR_PIN 23
+#define Y_MIN_PIN 19
+#define Y_MAX_PIN -1
+
+#define Z_STEP_PIN 3
+#define Z_DIR_PIN 2
+#define Z_MIN_PIN 20
+#define Z_MAX_PIN -1
+
+#define E0_STEP_PIN 1
+#define E0_DIR_PIN 0
+
+#define PROBE_PIN 20
+
+#define LED_PIN -1
+#define FAN_PIN 12
+
+#define PS_ON_PIN -1
+#define KILL_PIN -1
+
+#define HEATER_0_PIN 13 // (extruder)
+#define HEATER_1_PIN -1
+#define HEATER_2_PIN -1
+
+#ifdef REPRAPPRO_HUXLEY
+ #define HEATER_BED_PIN 10 // bed (change to 10 for gate pin of MOSFET on heated bed)
+#else
+ #define HEATER_BED_PIN 12
+#endif
+#define X_ENABLE_PIN 14
+#define Y_ENABLE_PIN 14
+#define Z_ENABLE_PIN 26
+#define E0_ENABLE_PIN 14
+
+#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
+#define TEMP_1_PIN -1
+#define TEMP_2_PIN -1
+#define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
+#define SDPOWER -1
+#define SDSS 31
+
+
+#endif
+
+/****************************************************************************************
+* Melzi pin assignment
+*
+****************************************************************************************/
+#if MOTHERBOARD == 63
+#define KNOWN_BOARD 1
+#ifndef __AVR_ATmega644P__
+#ifndef __AVR_ATmega1284P__
+#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
+#endif
+#endif
+
+#define X_STEP_PIN 15
+#define X_DIR_PIN 21
+#define X_MIN_PIN 18
+#define X_MAX_PIN -2
+
+#define Y_STEP_PIN 22
+#define Y_DIR_PIN 23
+#define Y_MIN_PIN 19
+#define Y_MAX_PIN -1
+
+#define Z_STEP_PIN 3
+#define Z_DIR_PIN 2
+#define Z_MIN_PIN 20
+#define Z_MAX_PIN -1
+
+#define E0_STEP_PIN 1
+#define E0_DIR_PIN 0
+
+#define PROBE_PIN -1 //29 on Melzi1284p A2
+
+#define LED_PIN 27
+#define M571_PIN 28
+
+#define FAN_PIN 4
+
+#define PS_ON_PIN -1
+#define KILL_PIN -1
+
+#define HEATER_0_PIN 13 // (extruder)
+#define HEATER_1_PIN -1
+#define HEATER_2_PIN -1
+#ifdef REPRAPPRO_HUXLEY
+ #define HEATER_BED_PIN 10 // bed (change to 10 for gate pin of MOSFET on heated bed)
+#else
+ #define HEATER_BED_PIN 12
+#endif
+#define X_ENABLE_PIN 14
+#define Y_ENABLE_PIN 14
+#define Z_ENABLE_PIN 26
+#define E0_ENABLE_PIN 14
+
+#define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
+#define TEMP_1_PIN -1
+#define TEMP_2_PIN -1
+#define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
+#define SDPOWER -1
+#define SDSS 31
+
+#define SLAVE_CLOCK 16
+
+#endif
+
+
+
+#ifndef KNOWN_BOARD
+#error Unknown MOTHERBOARD value in configuration.h
+#endif
+
+//List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
+#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, HEATER_0_PIN,
+#ifdef REPRAPPRO_MULTIMATERIALS
+ #define _E1_PINS -1, -1, -1, -1,
+ #define _E2_PINS -1, -1, -1, -1,
+#else
+#if EXTRUDERS > 1
+ #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, HEATER_1_PIN,
+#else
+ #define _E1_PINS
+#endif
+#if EXTRUDERS > 2
+ #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, HEATER_2_PIN,
+#else
+ #define _E2_PINS
+#endif
+#endif
+
+#ifdef DISABLE_MAX_ENDSTOPS
+#define X_MAX_PIN -1
+#define Y_MAX_PIN -1
+#define Z_MAX_PIN -1
+#endif
+
+#define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, LED_PIN, PS_ON_PIN, \
+ HEATER_BED_PIN, FAN_PIN, \
+ _E0_PINS _E1_PINS _E2_PINS \
+ TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN, TEMP_BED_PIN }
+
+#endif