comparison: pins.h
pins.h
- changeset 0
- 2c8ba1964db7
equal
deleted
inserted
replaced
| -1:000000000000 | 0:2c8ba1964db7 |
|---|---|
| 1 #ifndef _PINS_H | |
| 2 #define _PINS_H | |
| 3 | |
| 4 /**************************************************************************************** | |
| 5 * Sanguinololu pin assignment | |
| 6 * | |
| 7 ****************************************************************************************/ | |
| 8 #if MOTHERBOARD == 62 | |
| 9 #define KNOWN_BOARD 1 | |
| 10 #ifndef __AVR_ATmega644P__ | |
| 11 #ifndef __AVR_ATmega1284P__ | |
| 12 #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. | |
| 13 #endif | |
| 14 #endif | |
| 15 | |
| 16 #define X_STEP_PIN 15 | |
| 17 #define X_DIR_PIN 21 | |
| 18 #define X_MIN_PIN 18 | |
| 19 #define X_MAX_PIN -1 | |
| 20 | |
| 21 #define Y_STEP_PIN 22 | |
| 22 #define Y_DIR_PIN 23 | |
| 23 #define Y_MIN_PIN 19 | |
| 24 #define Y_MAX_PIN -1 | |
| 25 | |
| 26 #define Z_STEP_PIN 3 | |
| 27 #define Z_DIR_PIN 2 | |
| 28 #define Z_MIN_PIN 20 | |
| 29 #define Z_MAX_PIN -1 | |
| 30 | |
| 31 #define E0_STEP_PIN 1 | |
| 32 #define E0_DIR_PIN 0 | |
| 33 | |
| 34 #define PROBE_PIN 20 | |
| 35 | |
| 36 #define LED_PIN -1 | |
| 37 #define FAN_PIN 12 | |
| 38 | |
| 39 #define PS_ON_PIN -1 | |
| 40 #define KILL_PIN -1 | |
| 41 | |
| 42 #define HEATER_0_PIN 13 // (extruder) | |
| 43 #define HEATER_1_PIN -1 | |
| 44 #define HEATER_2_PIN -1 | |
| 45 | |
| 46 #ifdef REPRAPPRO_HUXLEY | |
| 47 #define HEATER_BED_PIN 10 // bed (change to 10 for gate pin of MOSFET on heated bed) | |
| 48 #else | |
| 49 #define HEATER_BED_PIN 12 | |
| 50 #endif | |
| 51 #define X_ENABLE_PIN 14 | |
| 52 #define Y_ENABLE_PIN 14 | |
| 53 #define Z_ENABLE_PIN 26 | |
| 54 #define E0_ENABLE_PIN 14 | |
| 55 | |
| 56 #define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) | |
| 57 #define TEMP_1_PIN -1 | |
| 58 #define TEMP_2_PIN -1 | |
| 59 #define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) | |
| 60 #define SDPOWER -1 | |
| 61 #define SDSS 31 | |
| 62 | |
| 63 | |
| 64 #endif | |
| 65 | |
| 66 /**************************************************************************************** | |
| 67 * Melzi pin assignment | |
| 68 * | |
| 69 ****************************************************************************************/ | |
| 70 #if MOTHERBOARD == 63 | |
| 71 #define KNOWN_BOARD 1 | |
| 72 #ifndef __AVR_ATmega644P__ | |
| 73 #ifndef __AVR_ATmega1284P__ | |
| 74 #error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. | |
| 75 #endif | |
| 76 #endif | |
| 77 | |
| 78 #define X_STEP_PIN 15 | |
| 79 #define X_DIR_PIN 21 | |
| 80 #define X_MIN_PIN 18 | |
| 81 #define X_MAX_PIN -2 | |
| 82 | |
| 83 #define Y_STEP_PIN 22 | |
| 84 #define Y_DIR_PIN 23 | |
| 85 #define Y_MIN_PIN 19 | |
| 86 #define Y_MAX_PIN -1 | |
| 87 | |
| 88 #define Z_STEP_PIN 3 | |
| 89 #define Z_DIR_PIN 2 | |
| 90 #define Z_MIN_PIN 20 | |
| 91 #define Z_MAX_PIN -1 | |
| 92 | |
| 93 #define E0_STEP_PIN 1 | |
| 94 #define E0_DIR_PIN 0 | |
| 95 | |
| 96 #define PROBE_PIN -1 //29 on Melzi1284p A2 | |
| 97 | |
| 98 #define LED_PIN 27 | |
| 99 #define M571_PIN 28 | |
| 100 | |
| 101 #define FAN_PIN 4 | |
| 102 | |
| 103 #define PS_ON_PIN -1 | |
| 104 #define KILL_PIN -1 | |
| 105 | |
| 106 #define HEATER_0_PIN 13 // (extruder) | |
| 107 #define HEATER_1_PIN -1 | |
| 108 #define HEATER_2_PIN -1 | |
| 109 #ifdef REPRAPPRO_HUXLEY | |
| 110 #define HEATER_BED_PIN 10 // bed (change to 10 for gate pin of MOSFET on heated bed) | |
| 111 #else | |
| 112 #define HEATER_BED_PIN 12 | |
| 113 #endif | |
| 114 #define X_ENABLE_PIN 14 | |
| 115 #define Y_ENABLE_PIN 14 | |
| 116 #define Z_ENABLE_PIN 26 | |
| 117 #define E0_ENABLE_PIN 14 | |
| 118 | |
| 119 #define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder) | |
| 120 #define TEMP_1_PIN -1 | |
| 121 #define TEMP_2_PIN -1 | |
| 122 #define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed) | |
| 123 #define SDPOWER -1 | |
| 124 #define SDSS 31 | |
| 125 | |
| 126 #define SLAVE_CLOCK 16 | |
| 127 | |
| 128 #endif | |
| 129 | |
| 130 | |
| 131 | |
| 132 #ifndef KNOWN_BOARD | |
| 133 #error Unknown MOTHERBOARD value in configuration.h | |
| 134 #endif | |
| 135 | |
| 136 //List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! | |
| 137 #define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, HEATER_0_PIN, | |
| 138 #ifdef REPRAPPRO_MULTIMATERIALS | |
| 139 #define _E1_PINS -1, -1, -1, -1, | |
| 140 #define _E2_PINS -1, -1, -1, -1, | |
| 141 #else | |
| 142 #if EXTRUDERS > 1 | |
| 143 #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, HEATER_1_PIN, | |
| 144 #else | |
| 145 #define _E1_PINS | |
| 146 #endif | |
| 147 #if EXTRUDERS > 2 | |
| 148 #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, HEATER_2_PIN, | |
| 149 #else | |
| 150 #define _E2_PINS | |
| 151 #endif | |
| 152 #endif | |
| 153 | |
| 154 #ifdef DISABLE_MAX_ENDSTOPS | |
| 155 #define X_MAX_PIN -1 | |
| 156 #define Y_MAX_PIN -1 | |
| 157 #define Z_MAX_PIN -1 | |
| 158 #endif | |
| 159 | |
| 160 #define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, LED_PIN, PS_ON_PIN, \ | |
| 161 HEATER_BED_PIN, FAN_PIN, \ | |
| 162 _E0_PINS _E1_PINS _E2_PINS \ | |
| 163 TEMP_0_PIN, TEMP_1_PIN, TEMP_2_PIN, TEMP_BED_PIN } | |
| 164 | |
| 165 #endif |
