--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/Configuration_adv.h Sat Nov 07 13:23:07 2015 +0100
@@ -0,0 +1,190 @@
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+
+
+#define BED_CHECK_INTERVAL 5000 //ms
+
+
+// Wait for Cooldown
+// This defines if the M109 call should not block if it is cooling down.
+// example: From a current temp of 220, you set M109 S200.
+// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
+#define CooldownNoWait true
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN 1.0
+
+//This is for controlling a fan to cool down the stepper drivers
+//it will turn on when any driver is enabled
+//and turn off after the set amount of seconds from last driver being disabled again
+//#define CONTROLLERFAN_PIN 23 //Pin used for the fan to cool controller, comment out to disable this function
+#define CONTROLLERFAN_SEC 60 //How many seconds, after all motors were disabled, the fan should run
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+// This defines the number of extruders
+#ifdef REPRAPPRO_MULTIMATERIALS
+#define EXTRUDERS 3
+#else
+#define EXTRUDERS 1
+#endif
+
+#define Z_INCREMENT .0040 //Probe Movement Increment - 1 Full step on Huxley = 1/250
+#define PROBE_N 3
+
+#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_RETRACT_MM 10
+#define Y_HOME_RETRACT_MM 10
+#define Z_HOME_RETRACT_MM 2
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+#define MAX_STEP_FREQUENCY 50000 // Max step frequency for Ultimaker (5000 pps / half step)
+
+//default stepper release if idle
+#define DEFAULT_STEPPER_DEACTIVE_TIME 60
+
+#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE 0.0
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
+#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT 15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+
+#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
+#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // no z because of layer shift.
+
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// hooke's law says: force = k * distance
+// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#ifdef ADVANCE
+ #define EXTRUDER_ADVANCE_K 0.015
+
+ #define D_FILAMENT 1.75
+ #define STEPS_MM_E 836
+ #define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
+ #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
+
+#endif // ADVANCE
+
+// Arc interpretation settings:
+#define MM_PER_ARC_SEGMENT 1
+#define N_ARC_CORRECTION 25
+
+const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
+
+// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
+// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
+// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
+// be commented out otherwise
+//#define SDCARDDETECTINVERTED
+
+//===========================================================================
+//=============================Buffers ============================
+//===========================================================================
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
+#if defined SDSUPPORT
+ #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+// Chuck size for fast sd transfer
+ #define SD_FAST_XFER_CHUNK_SIZE 1024
+#else
+ #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+
+//The ASCII buffer for recieving from the serial:
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 4
+
+//===========================================================================
+//============================= Define Defines ============================
+//===========================================================================
+/*
+#if TEMP_SENSOR_0 > 0
+ #define THERMISTORHEATER_0 TEMP_SENSOR_0
+ #define HEATER_0_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_1 > 0
+ #define THERMISTORHEATER_1 TEMP_SENSOR_1
+ #define HEATER_1_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_2 > 0
+ #define THERMISTORHEATER_2 TEMP_SENSOR_2
+ #define HEATER_2_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_BED > 0
+ #define THERMISTORBED TEMP_SENSOR_BED
+ #define BED_USES_THERMISTOR
+#endif
+#if TEMP_SENSOR_0 == -1
+ #define HEATER_0_USES_AD595
+#endif
+#if TEMP_SENSOR_1 == -1
+ #define HEATER_1_USES_AD595
+#endif
+#if TEMP_SENSOR_2 == -1
+ #define HEATER_2_USES_AD595
+#endif
+#if TEMP_SENSOR_BED == -1
+ #define BED_USES_AD595
+#endif
+#if TEMP_SENSOR_0 == -2
+ #define HEATER_0_USES_MAX6675
+#endif
+#if TEMP_SENSOR_0 == 0
+ #undef HEATER_0_MINTEMP
+ #undef HEATER_0_MAXTEMP
+#endif
+#if TEMP_SENSOR_1 == 0
+ #undef HEATER_1_MINTEMP
+ #undef HEATER_1_MAXTEMP
+#endif
+#if TEMP_SENSOR_2 == 0
+ #undef HEATER_2_MINTEMP
+ #undef HEATER_2_MAXTEMP
+#endif
+#if TEMP_SENSOR_BED == 0
+ #undef BED_MINTEMP
+ #undef BED_MAXTEMP
+#endif
+*/
+
+#endif //__CONFIGURATION_ADV_H