comparison: Configuration_mendel2.h
Configuration_mendel2.h
- changeset 3
- 770b218a4931
equal
deleted
inserted
replaced
| 2:b373b0288715 | 3:770b218a4931 |
|---|---|
| 1 // Bed thermistor: Rapid 61-0446 ; Semitec 103GT-2 - All Mendel2 shipped after 1/4/13 (launch) | |
| 2 // #define BED_BETA 4126.0 | |
| 3 // #define BED_NTC 10000.0 | |
| 4 | |
| 5 // Bed thermistor: Farnell 1299930 ; EPCOS B57863S103F040 - All Mendel2 shipped after 29/5/14 | |
| 6 #define BED_BETA 3988.0 | |
| 7 #define BED_NTC 10000.0 | |
| 8 | |
| 9 // Extruder thermistor: RS 198-961 100k ohm 10% DO-35 NTC thermistor - All Mendel2 shipped after 1/4/13 (launch) | |
| 10 // #define E_BETA 3960.0 | |
| 11 // #define E_NTC 100000.0 | |
| 12 | |
| 13 // Extruder thermistor: Digikey 480-3137-ND - All Mendels shipped after 25/2/14 | |
| 14 #define E_BETA 4138.0 | |
| 15 #define E_NTC 100000.0 | |
| 16 | |
| 17 #define AXES_MAX_LENGTHS {210, 210, 140} | |
| 18 #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true | |
| 19 #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false | |
| 20 #define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true | |
| 21 #define INVERT_E0_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false | |
| 22 #define INVERT_E1_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false | |
| 23 #define INVERT_E2_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false | |
| 24 | |
| 25 #define X_MAX_LENGTH 210 | |
| 26 #define Y_MAX_LENGTH 210 | |
| 27 #define Z_MAX_LENGTH 110 | |
| 28 #define HOMING_FEEDRATE {10*60, 10*60, 1*60, 0} // set the homing speeds (mm/min) | |
| 29 #define FAST_HOME_FEEDRATE {50*60, 50*60, 1*60, 0} // set the homing speeds (mm/min) | |
| 30 | |
| 31 #define DEFAULT_MAX_FEEDRATE {300, 300, 3, 45} // (mm/sec) | |
| 32 #define DEFAULT_MAX_ACCELERATION {1000,1000,30,250} // X, Y, Z, E maximum start speed for accelerated moves. E default values | |
| 33 | |
| 34 // X, Y, Z, E steps per mm | |
| 35 #define DEFAULT_AXIS_STEPS_PER_UNIT {92.635, 92.635, 4000, 660} // <- 17-tooth printed pulley |
