comparison: Configuration_adv.h
Configuration_adv.h
- changeset 3
- 770b218a4931
- parent 0
- 2c8ba1964db7
equal
deleted
inserted
replaced
| 2:b373b0288715 | 3:770b218a4931 |
|---|---|
| 2 #define CONFIGURATION_ADV_H | 2 #define CONFIGURATION_ADV_H |
| 3 | 3 |
| 4 //=========================================================================== | 4 //=========================================================================== |
| 5 //=============================Thermal Settings ============================ | 5 //=============================Thermal Settings ============================ |
| 6 //=========================================================================== | 6 //=========================================================================== |
| 7 | |
| 8 | |
| 9 #define BED_CHECK_INTERVAL 5000 //ms | 7 #define BED_CHECK_INTERVAL 5000 //ms |
| 10 | 8 |
| 11 | 9 |
| 12 // Wait for Cooldown | 10 // Wait for Cooldown |
| 13 // This defines if the M109 call should not block if it is cooling down. | 11 // This defines if the M109 call should not block if it is cooling down. |
| 30 //=============================Mechanical Settings=========================== | 28 //=============================Mechanical Settings=========================== |
| 31 //=========================================================================== | 29 //=========================================================================== |
| 32 | 30 |
| 33 // This defines the number of extruders | 31 // This defines the number of extruders |
| 34 #ifdef REPRAPPRO_MULTIMATERIALS | 32 #ifdef REPRAPPRO_MULTIMATERIALS |
| 35 #define EXTRUDERS 3 | 33 #define EXTRUDERS 3 |
| 36 #else | 34 #else |
| 37 #define EXTRUDERS 1 | 35 #define EXTRUDERS 1 |
| 38 #endif | 36 #endif |
| 39 | 37 |
| 40 #define Z_INCREMENT .0040 //Probe Movement Increment - 1 Full step on Huxley = 1/250 | 38 #define Z_INCREMENT .0040 //Probe Movement Increment - 1 Full step on Huxley = 1/250 |
| 41 #define PROBE_N 3 | 39 #define PROBE_N 3 |
| 42 | 40 |
| 43 #define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing | 41 #define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing |
| 44 | 42 |
| 45 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. | 43 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. |
| 46 | 44 |
| 47 //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: | 45 //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: |
| 48 #define X_HOME_RETRACT_MM 10 | 46 #define X_HOME_RETRACT_MM 2 |
| 49 #define Y_HOME_RETRACT_MM 10 | 47 #define Y_HOME_RETRACT_MM 2 |
| 50 #define Z_HOME_RETRACT_MM 2 | 48 #define Z_HOME_RETRACT_MM 1.5 |
| 51 | 49 |
| 52 #define AXIS_RELATIVE_MODES {false, false, false, false} | 50 #define AXIS_RELATIVE_MODES {false, false, false, false} |
| 53 | 51 |
| 54 #define MAX_STEP_FREQUENCY 50000 // Max step frequency for Ultimaker (5000 pps / half step) | 52 #define MAX_STEP_FREQUENCY 50000 // Max step frequency for Ultimaker (5000 pps / half step) |
| 55 | 53 |
| 61 | 59 |
| 62 // minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff. | 60 // minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff. |
| 63 #define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this | 61 #define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this |
| 64 | 62 |
| 65 // If defined the movements slow down when the look ahead buffer is only half full | 63 // If defined the movements slow down when the look ahead buffer is only half full |
| 66 #define SLOWDOWN | 64 // #define SLOWDOWN |
| 67 | 65 |
| 68 // Frequency limit | 66 // Frequency limit |
| 69 // See nophead's blog for more info | 67 // See nophead's blog for more info |
| 70 // Not working O | 68 // Not working O |
| 71 //#define XY_FREQUENCY_LIMIT 15 | 69 //#define XY_FREQUENCY_LIMIT 15 |
| 120 //=========================================================================== | 118 //=========================================================================== |
| 121 | 119 |
| 122 // The number of linear motions that can be in the plan at any give time. | 120 // The number of linear motions that can be in the plan at any give time. |
| 123 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering. | 121 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering. |
| 124 #if defined SDSUPPORT | 122 #if defined SDSUPPORT |
| 125 #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller | 123 //#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller |
| 126 // Chuck size for fast sd transfer | 124 #define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller |
| 127 #define SD_FAST_XFER_CHUNK_SIZE 1024 | 125 // Chuck size for fast sd transfer |
| 126 #define SD_FAST_XFER_CHUNK_SIZE 1024 | |
| 128 #else | 127 #else |
| 129 #define BLOCK_BUFFER_SIZE 16 // maximize block buffer | 128 #define BLOCK_BUFFER_SIZE 64 // maximize block buffer |
| 130 #endif | 129 #endif |
| 131 | 130 |
| 132 | 131 |
| 133 //The ASCII buffer for recieving from the serial: | 132 //The ASCII buffer for recieving from the serial: |
| 134 #define MAX_CMD_SIZE 96 | 133 #define MAX_CMD_SIZE 96 |
